LUO Ren, CENG Jing, DAI Huan-yun, TENG Wan-xiu. Running adaptability of high-speed EMU[J]. Journal of Traffic and Transportation Engineering, 2011, 11(6): 37-43. doi: 10.19818/j.cnki.1671-1637.2011.06.006
Citation: LUO Ren, CENG Jing, DAI Huan-yun, TENG Wan-xiu. Running adaptability of high-speed EMU[J]. Journal of Traffic and Transportation Engineering, 2011, 11(6): 37-43. doi: 10.19818/j.cnki.1671-1637.2011.06.006

Running adaptability of high-speed EMU

doi: 10.19818/j.cnki.1671-1637.2011.06.006
More Information
  • Author Bio:

    LUO Ren (1979-), male, associate researcher, PhD, +86-28-86466085, luorenswjtu@tom.com

  • Received Date: 2011-07-21
  • Publish Date: 2011-12-25
  • A nonlinear dynamics simulation model of vehicle system was set up for high-speed EMU(electric multiple units).The actual running conditions were considered, the numerical simulation method was adopted to research the running adaptability and stability of EMU, and the matching relationships of wheel profile wear and wheel/rail contact geometry, primary guiding stiffness and equivalent conicity were analyzed.Analysis result indicates that wheel/rail matching relationship and vehicle suspension parameters are the most important factors affecting the running adaptability.The hollow wear of wheel tread has greater influence on the running stability than the uniform wear with the same wear depth.The bogie with large guiding stiffness is unstable when the low conicity tread is used, while the bogie with small guiding stiffness is also unstable when the equivalent conicity increases because of wear.In the design process of EMU, the proper wheel/rail profile matching relationship and suspension parameter optimization are determined according to the dynamics requirement of running line.For the bogie with small primary guiding stiffness, LMA type wheel tread with small initial conicity is used.While for the bogie with large guiding stiffness, wheel/rail matching relationship with equivalent conicity larger than 0.10 is required.During EMU operation, the hollow wear of wheel tread should be prevented, and the reasonable rail profile is maintained through grinding rail.

     

  • loading
  • [1]
    JIN Xue-song, GUO Jun, XIAO Xin-biao, et al. Key scientific problems in the study on running safety of high speed trains[J]. Engineering Mechanics, 2009, 26(S2): 8-22, 105. (in Chinese) http://www.cnki.com.cn/Article/CJFDTOTAL-GCLX2009S2004.htm
    [2]
    LI Yan, ZHANG Wei-hua, ZHOU Wen-xiang. Influence of wear of wheel profile on dynamic performance of EMU[J]. Journal of Southwest Jiaotong University, 2010, 45(4): 549-554. (in Chinese) doi: 10.3969/j.issn.0258-2724.2010.04.011
    [3]
    ZHANG Hong, YU Da-lian, MA Li-jun. Research on thed ynamics of high-speed train[J]. Electric Drive for Locomotives, 2010(5): 9-14. (in Chinese) http://www.cnki.com.cn/Article/CJFDTOTAL-JCDC201005003.htm
    [4]
    SUN Xiao-jie, ZHOU Wen-xiang. Tread wear and its effect on wheel-rail contact geometry[J]. Rolling Stock, 2010, 48(7): 1-4, 14. (in Chinese) doi: 10.3969/j.issn.1002-7602.2010.07.001
    [5]
    SCHEUNEMANN E, WU Xin-min. Wheel/rail geometry—the common subject of rail vehicles and track[J]. Foreign Rolling Stock, 2007, 44(2): 21-27. (in Chinese) doi: 10.3969/j.issn.1002-7610.2007.02.004
    [6]
    WRANG M. Instability phenomena of a passenger coach, caused by internal yaw damper flexibility[J]. Vehicle System Dynamics, 1999, 33(S): 406-417.
    [7]
    WICKENS A H. Fundamentals of rail vehicle dynamics: guidance and stability[M]. Netherlands: Swets & Zeitlinger Publishers, 2003.
    [8]
    GOODALL R M, IWNICKI S D. Non-linear dynamic techniques v. equivalent conicity methods for rail vehicle stability assessment[J]. Vehicle System Dynamics, 2004, 41(S): 791-799.
    [9]
    LUO Ren, ZENG Jing, WU Ping-bo, et al. Influence of wheel/rail parameters on wheel profile wear of high-speed train[J]. Journal of Traffic and Transportation Engineering, 2009, 9(6): 47-53. (in Chinese) doi: 10.3969/j.issn.1671-1637.2009.06.010
    [10]
    WANG Kai-yun, SI Dao-lin, CHEN Zhong-hua. Wheel-rail dynamic interaction characteristic on high-speed railway[J]. Journal of Traffic and Transportation Engineering, 2008, 8(5): 15-18. (in Chinese) doi: 10.3321/j.issn:1671-1637.2008.05.003
    [11]
    ZHANG Wei-hua. Study on innovation technique of train bogie at high speed[J]. Engineering Sciences, 2009, 11(10): 8-18. (in Chinese) doi: 10.3969/j.issn.1009-1742.2009.10.002
    [12]
    LIANG Shu-lin, PIAO Ming-wei, ZHANG Xiang-jie, et al. Investigation of non-linear effects on high-speed vehicle lateral stability[J]. Journal of the China Railway Society, 2009, 31(5): 23-30. (in Chinese) doi: 10.3969/j.issn.1001-8360.2009.05.004
    [13]
    CHENG Di, WANG Cheng-guo, LIU Jin-zhao, et al. Application analysis comparison of two response surface methods for the optimization of the wheel tread[J]. China Railway Science, 2010, 31(3): 64-69. (in Chinese) http://www.cnki.com.cn/Article/CJFDTOTAL-ZGTK201003013.htm
    [14]
    JIN Xue-song, DU Xing, GUO Jun, et al. State of arts of research on rail grinding[J]. Journal of Southwest Jiaotong University, 2010, 45(1): 1-11. (in Chinese) http://www.cnki.com.cn/Article/CJFDTOTAL-XNJT201001002.htm

Catalog

    Article Metrics

    Article views (2201) PDF downloads(1034) Cited by()
    Related

    /

    DownLoad:  Full-Size Img  PowerPoint
    Return
    Return