Volume 21 Issue 6
Dec.  2021
Turn off MathJax
Article Contents
Article Navigation >  Journal of Traffic and Transportation Engineering  > 2021  >  21(6): 40-62
Next Previous
ZUO Jian-yong, DING Jing-xian. Research progress on intelligent control and maintenance technology of railway vehicle braking system[J]. Journal of Traffic and Transportation Engineering, 2021, 21(6): 40-62. doi: 10.19818/j.cnki.1671-1637.2021.06.004
Citation: ZUO Jian-yong, DING Jing-xian. Research progress on intelligent control and maintenance technology of railway vehicle braking system[J]. Journal of Traffic and Transportation Engineering, 2021, 21(6): 40-62. doi: 10.19818/j.cnki.1671-1637.2021.06.004
shu

Research progress on intelligent control and maintenance technology of railway vehicle braking system

doi: 10.19818/j.cnki.1671-1637.2021.06.004

  • Institute of Rail Transit, Tongji University, Shanghai 201804, China

Funds:

National Key Research and Development Program of China 2018YFB1201603-13

National Natural Science Foundation of China 51775386

More Information
  • Author Bio:

    ZUO Jian-yong(1976-), male, professor, PhD, zuojy@tongji.edu.cn

  • Received Date: 2021-06-13
  • Publish Date: 2021-12-25
    Abstract
  • Focusing on the microcomputer-controlled direct electro-pneumatic braking system commonly used in railway vehicle, the structural composition, working principle, and control principle of the braking system were introduced, the technical characteristics of the braking system were analyzed, and the technical development trend of the intelligent braking system was summarized and discussed. The research status and existing problems of the braking system were reviewed from the two aspects of intelligent control and intelligent maintenance. Research result shows that the braking system of the railway vehicle is a complex mechanic-electric-pneumatic(hydraulic) coupled dynamic time-varying nonlinear control system, and its service process and failure behavior have the characteristics of uncertainty, fuzziness, and small samples. In terms of braking system control technology, compared with the theoretical braking force control, the two braking control modes of speed adhesion control and deceleration control have improved control effects when dealing with external interference. Aiming at uncertain factors such as external interference, performance degradation, or latent faults in the control of the braking system, an autonomous intelligent control based on parameter identification and closed-loop feedback is the development trend of the intelligent control technology of the braking system. The core goal is to realize the self-adaptation of external interference, self-maintenance of performance degradation, and self-adjustment of latent faults. With respect to braking system maintenance technology, the operation and maintenance of the braking system mainly involve condition monitoring and fault diagnosis, and few studies exist on fault prognosis and condition assessment. Making full use of the service status information of the braking system and strengthening the research on the service behavior and evolution law of the braking system under the coupled effect of multi-source factors are the development trend of the intelligent maintenance technology of the braking system. Further research should be conducted on service performance consistency analysis and evaluation, sensor layout optimization, and remaining useful life prediction methods of the braking system. 6 figs, 90 refs.

     

    • FullText(HTML)
  • loading
    • References(90)
  • [1]
    PENG Qi-yuan, LI Jian-guang, YANG Yu-xiang, et al. Influences of high-speed railway construction on railway transportation of China[J]. Journal of Southwest Jiaotong University, 2016, 51(3): 525-533. (in Chinese) doi: 10.3969/j.issn.0258-2724.2016.03.011
    [2]
    JIA Li-min, QIN Yong, LI Ping. The overall framework and key technologies of a new generation of rail intelligent transportation system[J]. China Railways, 2015(4): 14-19, 60. (in Chinese) doi: 10.3969/j.issn.1001-683X.2015.04.003
    [3]
    BAI Yan-chao, AN Chao, LI Ming-gao, et al. Tracking research on service performance of CRH3 EMU in Wuhan-Guangzhou Passenger Dedicated Line[J]. Railway Locomotive and Motor Car, 2018(1): 37-40, 43. (in Chinese) http://www.cnki.com.cn/Article/CJFDTOTAL-LRJX201801011.htm
    [4]
    TIAN Yong-zhu, SHA Miao, SHI Xue-ling, et al. The safety evaluation method for service of traction system on multiple units and research on standards[J]. Rolling Stock, 2015, 53(3): 21-24. (in Chinese) doi: 10.3969/j.issn.1002-7602.2015.03.005
    [5]
    WU Meng-ling, WANG Xiao-yan, YAN Kai-jun. Analysis by FMEA and FTA method of micro-computer controlled directacting electro-pneumatic braking system[J]. Electric Drive for Locomotives, 2008(1): 32-36. (in Chinese) http://www.cnki.com.cn/Article/CJFDTOTAL-JCDC200801007.htm
    [6]
    ZHAN Cheng-yi, CHENG Guang-hua, WANG Xiao-yan, et al. A test of valves in micro-computer controlled braking system[J]. Urban Mass Transit, 2008, 11(3): 30-34. (in Chinese) doi: 10.3969/j.issn.1007-869X.2008.03.008
    [7]
    PERIS E, GOIKOETXEA J. Roll2Rail: new dependable rolling stock for a more sustainable, intelligent and comfortable rail transport in Europe[J]. Transportation Research Procedia, 2016, 14: 567-574. doi: 10.1016/j.trpro.2016.05.294
    [8]
    MIAO Bing-rong, ZHANG Wei-hua, CHI Mao-ru, et al. Analysis and prospects of key technical features of next generation high speed trains[J]. Journal of the China Railway Society, 2019, 41(3): 58-70. (in Chinese) doi: 10.3969/j.issn.1001-8360.2019.03.008
    [9]
    LI Xiao-jun, LIU Zong-zhu, ZHANG Lei, et al. Scheme design and research of intelligent high-speed train[C]//China Intelligent Transportation Association. Proceedings of the 8th China Intelligent Transportation Annual Conference—Rail Transit. Beijing: Publishing House of Electronics Industry, 2013: 455-460. (in Chinese)
    [10]
    HALTUF M. Shift2Rail JU from member state's point of view[J]. Transportation Research Procedia, 2016, 14: 1819-1828. doi: 10.1016/j.trpro.2016.05.148
    [11]
    WU Meng-ling, MA Tian-he, TIAN Chun, et al. Discussion on development trend of train braking technology[J]. China Railway Science, 2019, 40(1): 134-144. (in Chinese) doi: 10.3969/j.issn.1001-4632.2019.01.18
    [12]
    WU Meng-ling, ZHOU Jia-jun, TIAN Chun, et al. Innovative technology of rail transit braking system[J]. Modern Urban Transit, 2019(7): 30-35. (in Chinese) http://www.cnki.com.cn/Article/CJFDTOTAL-XDGD201907007.htm
    [13]
    LIU Yu-xiang, FANG Chang-zheng, WAN Jian-bing. Technology status and development trend of train braking system[J]. Electric Locomotives and Mass Transit Vehicles, 2014, 37(5): 1-4. (in Chinese) http://www.cnki.com.cn/Article/CJFDTOTAL-DJJI201405003.htm
    [14]
    WU Meng-ling, CHENG Guang-hua, WANG Xiao-yan, et al. Discussion of braking deceleration control of railway vehicles[J]. Journal of the China Railway Society, 2009, 31(1): 94-97. (in Chinese) http://www.cnki.com.cn/Article/CJFDTOTAL-TDXB200901023.htm
    [15]
    ISHIZAKA K, LEWIS S R, LEWIS R. The low adhesion problem due to leaf contamination in the wheel/rail contact: bonding and low adhesion mechanisms[J]. Wear, 2017, 378/379: 183-197. doi: 10.1016/j.wear.2017.02.044
    [16]
    WHITE B T, NILSSON R, OLOFSSON U, et al. Effect of the presence of moisture at the wheel-rail interface during dew and damp conditions[J]. Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit, 2018, 232(4): 979-989. doi: 10.1177/0954409717706251
    [17]
    QI Zhuang, LI Fu, DING Jun-jun. Braking optimization method of wagon under limit adhesion[J]. Journal of Traffic and Transportation Engineering, 2012, 12(6): 35-40, 54. (in Chinese) doi: 10.3969/j.issn.1671-1637.2012.06.006
    [18]
    WU Bing, AN Bo-yang, WEN Ze-feng, et al. Wheel-rail low adhesion issues and its effect on wheel-rail material damage at high speed under different interfacial contaminations[J]. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 2019, 233(15): 5477-5490. doi: 10.1177/0954406219842285
    [19]
    LUO Ren, ZENG Jing. Anti-sliding control simulation of railway vehicle braking[J]. Chinese Journal of Mechanical Engineering, 2008, 44(3): 29-34. (in Chinese) doi: 10.3321/j.issn:0577-6686.2008.03.005
    [20]
    LI Jiang-hong, MA Jian, PENG Hui-shui. Basic principle and methods of adhesion control of locomotive[J]. Electric Drive for Locomotive, 2002(6): 4-8. (in Chinese) doi: 10.3969/j.issn.1000-128X.2002.06.002
    [21]
    ZUO Jian-yong, CHEN Zhong-kai. Antiskid control of railway train braking based on adhesion creep behavior[J]. Chinese Journal of Mechanical Engineering, 2012, 25(3): 543-549. doi: 10.3901/CJME.2012.03.543
    [22]
    ZHANG Hong-fei, WANG Wen-jian, SHEN Peng, et al. Experimental study on wheel/rail adhesion characteristics under oil medium condition[J]. China Railway Science, 2012, 33(4): 65-68. doi: 10.3969/j.issn.1001-4632.2012.04.11
    [23]
    WU Meng-ling, ZHOU Jia-jun, MA Tian-he, et al. Experimental study on wheel-rail brake adhesion under water condition[J]. Railway Locomotive and Car, 2021, 41(5): 139-143. doi: 10.3969/j.issn.1008-7842.2021.05.24
    [24]
    ZHOU Jia-jun, WU Meng-ling, TIAN Chun, et al. Experimental investigation on wheel-rail adhesion characteristics under water and large sliding conditions[J]. Industrial Lubrication and Tribology, 2021, 73(2): 366-372. doi: 10.1108/ILT-07-2020-0236
    [25]
    SHEN Z Y, HEDRICK J K, ELKINS J A. A comparison of alternative creep force models for rail vehicle dynamic analysis[J]. Vehicle System Dynamics, 1983, 12(1/2/3): 79-83. doi: 10.1080/00423118308968725
    [26]
    JIN Xue-song, WU Ping-bo, WEN Ze-feng. Effects of structure elastic deformations of wheelset and track on creep forces of wheel/rail in rolling contact[J]. Wear, 2002, 253(1/2): 247-256. http://www.sciencedirect.com/science/article/pii/S0043164802001084
    [27]
    SHRESTHA S, SPIRYAGIN M, WU Q. Friction condition characterization for rail vehicle advanced braking system[J]. Mechanical Systems and Signal Processing, 2019, 134: 106324. doi: 10.1016/j.ymssp.2019.106324
    [28]
    KIM Y M, KIM Y G, KIM S W, et al. Estimation of the adhesion force for a disc brake in a skid control condition[J]. International Journal of Automotive Technology, 2010, 11(5): 673-680. doi: 10.1007/s12239-010-0080-7
    [29]
    GU Bo-chuan. Locomotive adhesion coefficient estimation based on SVD strong track filter[J]. Railway Locomotive and Car, 2011, 31(4): 26-30. (in Chinese) doi: 10.3969/j.issn.1008-7842.2011.04.006
    [30]
    LI Ning-zhou, FENG Xiao-yun. Intelligent fuzzy optimal control of locomotive adhesion based on adaptive multiple subgroup collaboration QPSO algorithm[J]. China Railway Science, 2014, 35(4): 100-107. (in Chinese) doi: 10.3969/j.issn.1001-4632.2014.04.15
    [31]
    WU Meng-ling, PENG Shun, LI Xiao-ping. Online estimation algorithm of adhesive force for train wheeltrack[J]. Journal of Tongji University (Natural Science), 2018, 46(3): 354-358, 388. (in Chinese) http://www.cnki.com.cn/Article/CJFDTOTAL-TJDZ201803012.htm
    [32]
    MA Tian-he, WU Meng-ling, TIAN Chun. Anti-skid control based on adhesion force observer for train pneumatic braking[J]. Journal of Tongji University (Natural Science), 2020, 48(11): 1668-1675. (in Chinese) http://www.cnki.com.cn/Article/CJFDTOTAL-TJDZ202011016.htm
    [33]
    WEI Wei, WANG Qiang. Influence of train brake on longitudinal impulse of a heavy haul train passing through a ramp[J]. Journal of Vibration and Shock, 2014, 33(5): 143-148. (in Chinese) http://www.cnki.com.cn/Article/CJFDTOTAL-ZDCJ201405027.htm
    [34]
    WEI Wei, HU Yang. Influence of train tail exhaust device on longitudinal force of train[J]. Journal of Traffic and Transportation Engineering, 2012, 12(5): 43-49, 63. (in Chinese) doi: 10.3969/j.issn.1671-1637.2012.05.006
    [35]
    LIU Hai-dong, SU Mei, PENG Hong-qin, et al. Braking performances of urban rail trains[J]. Journal of Transportation Systems Engineering and Information Technology, 2011, 11(6): 93-97. doi: 10.3969/j.issn.1009-6744.2011.06.014
    [36]
    ZHAO Jian-fei. Braking control technology of new generation metro vehicle based on deceleration control[J]. Modern Urban Transit, 2019(11): 39-46. (in Chinese) http://www.cnki.com.cn/Article/CJFDTOTAL-XDGD201911008.htm
    [37]
    NANJING Zheng-xin, PENG Hui-min. Development of a braking device equipped with deceleration feedback function[J]. Foreign Locomotive and Rolling Stock Technology, 2013(2): 1-6. (in Chinese) http://www.cnki.com.cn/Article/CJFDTOTAL-GWJQ201302004.htm
    [38]
    NANKYO M, ISHIHARA T, INOOKA H. Feedback control of braking deceleration on railway vehicle[J]. Journal of Dynamic Systems, Measurement, and Control, 2006, 128(2): 244-250. doi: 10.1115/1.2192825
    [39]
    NANKYO M, ISHIHARA T, INOOKA H. Feedback control of brake system on railway vehicle considering non-linear property and dead time[C]//ASME. 2003 ASME International Mechanical Engineering Congress. New York: ASME, 2003: 99-104.
    [40]
    ZHANG Meng-nan, XU Hong-ze. Design of urban rail vehicle brake controller based on Krasovskii functionals[J]. Journal of Jilin University (Engineering and Technology Edition), 2015, 45(1): 104-111. (in Chinese) http://www.cnki.com.cn/Article/CJFDTOTAL-JLGY201501016.htm
    [41]
    WU Meng-ling, LUO Zhuo-jun. Study on train braking deceleration feedback control based on adaptive parameter estimation[J]. Journal of the China Railway Society, 2015, 37(8): 8-16. (in Chinese) doi: 10.3969/j.issn.1001-8360.2015.08.002
    [42]
    ZHOU Jia-jun, WU Meng-ling, LIU Yu-kang, et al. Train braking deceleration control based on improved Smith estimator[J]. Journal of Tongji University (Natural Science), 2020, 48(11): 1657-1667. (in Chinese) http://www.cnki.com.cn/Article/CJFDTOTAL-TJDZ202011015.htm
    [43]
    DENG Li-ming. Fault mode statistic and analysis of EMU[D]. Beijing: China Academy of Railway Sciences, 2015. (in Chinese)
    [44]
    XIN Zhi-qiang, XU Wen-yao, QIAO Feng. Fault screening process for relay valve of CRH EMUs[J]. Railway Locomotive and Car, 2017, 37(3): 94-96. (in Chinese) doi: 10.3969/j.issn.1008-7842.2017.03.23
    [45]
    ZUO Jian-yong, HAN Fei, Hu Wei. Reproduction simulation of emergency brake fault feature for subway train[J]. Journal of Traffic and Transportation Engineering, 2015, 15(5): 44-49, 56. (in Chinese) doi: 10.3969/j.issn.1671-1637.2015.05.006
    [46]
    ZHOU Bin, XIE Ming-yuan, WU Ke-ming. Analysis and prediction on the current situation of the repair class and repair system of electric multiple units (EMU)[J]. Electric Drive for Locomotives, 2017(1): 17-21. (in Chinese) http://www.cnki.com.cn/Article/CJFDTOTAL-JCDC201701006.htm
    [47]
    CHANG Zhen-chen, ZHANG Hai-feng. Application state and prospects of PHM technology on EMU[J]. Electric Locomotives and Mass Transit Vehicles, 2016, 39(1): 1-4. (in Chinese) http://www.cnki.com.cn/Article/CJFDTOTAL-DJJI201601001.htm
    [48]
    TAI Xiu-hua, GUO Tian-xu, ZHANG Ying-jia, et al. Technical research on prognostics and health management for braking systems[J]. Rolling Stock, 2018, 56 (11): 5-8. (in Chinese) doi: 10.3969/j.issn.1002-7602.2018.11.003
    [49]
    LIANG Jian-ying. Research on intelligent diagnosis and fault prediction technology for high speed trains[J]. Journal of Beijing Jiaotong University, 2019, 43(1): 63-70. (in Chinese) doi: 10.11860/j.issn.1673-0291.2019.01.007
    [50]
    LIU Zhi-liang, PAN Deng, ZUO Ming-jian, et al. A review on fault diagnosis for rail vehicles[J]. Journal of Mechanical Engineering, 2016, 52(14): 134-146. (in Chinese) http://www.cnki.com.cn/Article/CJFDTOTAL-JXXB201614015.htm
    [51]
    ZHANG Yang. Research on PHM scheme of EMU brake system[J]. Railway Locomotive and Car, 2020, 40(5): 19-22. (in Chinese) doi: 10.3969/j.issn.1008-7842.2020.05.04
    [52]
    LIU Yuan-qing, GENG Xiao-feng, QI Cheng. Research and application of braking system with PHM technology in urban rail transit[J]. Modern Urban Transit, 2019(9): 24-28. (in Chinese) http://www.cnki.com.cn/Article/CJFDTOTAL-XDGD201909004.htm
    [53]
    GAO Dian-zhu, ZHANG Shi-feng, LIU Wei-rong. Key technologies and system implementation of predictable maintenance of locomotive braking system[J]. Electric Locomotives and Mass Transit Vehicles, 2018, 41(2): 1-6. (in Chinese) http://www.cnki.com.cn/Article/CJFDTOTAL-DJJI201802001.htm
    [54]
    ZUO Jian-yong, LIU Yin-hu, DING Jing-xian, et al. Fault identification diagnosis and maintenance for high-speed train braking system[J]. Railway Locomotive and Car, 2021, 41(5): 156-162. doi: 10.3969/j.issn.1008-7842.2021.05.27
    [55]
    GAO Min, WANG Xue-mei, NI Wen-bo. Study on vehicle braking monitor device based on S3C2410X[J]. China Measurement Technology, 2007, 33(5): 142-144. (in Chinese) http://www.cnki.com.cn/Article/CJFDTOTAL-SYCS200705044.htm
    [56]
    LI Wan-xin, ZHANG Yang, LIN Rong-wen, et al. Fault diagnosis and safety measures of EMU braking system[J]. Railway Locomotive and Car, 2011, 31(5): 39-42. (in Chinese) doi: 10.3969/j.issn.1008-7842.2011.05.008
    [57]
    ZHANG Yong-chun. Real-time monitoring and fault diagnosis expert system for locomotive braking system[J]. Computer Measurement and Control, 2013, 21(10): 2615-2617, 2620. (in Chinese) doi: 10.3969/j.issn.1671-4598.2013.10.002
    [58]
    KAN Jia-yu. Research on the methods of condition monitoring based on vector quantization for train brake pad temperature[D]. Beijing: Beijing Jiaotong University, 2015. (in Chinese)
    [59]
    ZUO Jian-yong, DING Jing-xian, HU Wei, et al. Performance degradation monitoring based on data fusion method for in-service train pneumatic brake system[J]. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 2019, 233(6): 1924-1938. doi: 10.1177/0954406218778882
    [60]
    ZHU Jian-qu, JIN Wei-dong, ZHENG Gao, et al. High-speed train running gear fault recognition based on information fusion of multi-source[J]. Journal of Vibration and Shock, 2014, 33(21): 183-188. (in Chinese) http://www.cnki.com.cn/Article/CJFDTOTAL-ZDCJ201421033.htm
    [61]
    ZHOU Dong-hua, LIU Yang, HE Xiao. Review on fault diagnosis techniques for closed-loop systems[J]. Acta Automatica Sinica, 2013, 39(11): 1933-1943. (in Chinese) http://www.cnki.com.cn/Article/CJFDTOTAL-MOTO201311020.htm
    [62]
    ZUO Jian-yong, CHEN Zhong-kai. Sensor configuration and test for fault diagnoses of subway braking system based on signed digraph method[J]. Chinese Journal of Mechanical Engineering, 2014, 27(3): 475-482. doi: 10.3901/CJME.2014.03.475
    [63]
    TIAN Jing-yi, YANG Ye, YANG Xue-feng, et al. Intelligent fault diagnosis method for high-speed trains[J]. Control and Instruments in Chemical Industry, 2013, 40(4): 531-533. (in Chinese) doi: 10.3969/j.issn.1000-3932.2013.04.027
    [64]
    MOU Zeng-xu. Software design of condition monitoring and fault diagnosis for EMUs brake system[D]. Chengdu: Southwest Jiaotong University, 2013. (in Chinese)
    [65]
    LIU De-dong. Research on the monitoring and fault diagnosis system of urban rail vehicle braking system[D]. Beijing: Beijing University of Civil Engineering and Architecture, 2014. (in Chinese)
    [66]
    ZHANG Tao. CCBⅡ brake based on multi-hierarchy fuzzy evaluation[J]. Electrical Engineering, 2009(4): 61-65. (in Chinese) doi: 10.3969/j.issn.1673-3800.2009.04.018
    [67]
    DING Guo-jun, WANG Li-de, SHEN Ping, et al. Sensor fault diagnosis based on EEMD energy entropy and LSSVM[J]. Transducer and Microsystem Technologies, 2013, 32(7): 22-25. (in Chinese) doi: 10.3969/j.issn.1000-9787.2013.07.007
    [68]
    LIU J, LI Y F, ZIO E. A SVM framework for fault detection of the braking system in a high speed train[J]. Mechanical Systems and Signal Processing, 2017, 87: 401-409. doi: 10.1016/j.ymssp.2016.10.034
    [69]
    LIU J, ZIO E. A scalable fuzzy support vector machine for fault detection in transportation systems[J]. Expert Systems With Applications, 2018, 102: 36-43. doi: 10.1016/j.eswa.2018.02.017
    [70]
    ZUO Jian-yong, DING Jing-xian, FENG Fu-ren. Latent leakage fault identification and diagnosis based on multi-source information fusion method for key pneumatic units in Chinese standard electric multiple units (EMU) braking system[J]. Applied Sciences, 2019, 9(2): 300. doi: 10.3390/app9020300
    [71]
    PEI Di. Research on fault diagnosis of railway wagon air brake system based on Bayesian network[D]. Beijing: Beijing Jiaotong University, 2018. (in Chinese)
    [72]
    YAN Shu-rong. Research and application on key technologies of fault diagnosis expert system for train brake[D]. Dalian: Dalian Jiaotong University, 2011. (in Chinese)
    [73]
    HOU Wen-ming. Research and application of fault online diagnosis technology for brake system of HXD1 locomotive[D]. Changsha: Central South University, 2010. (in Chinese)
    [74]
    NIU Gang, XIONG Liu-jing, QIN Xiao-xiao, et al. Fault detection isolation and diagnosis of multi-axle speed sensors for high-speed trains[J]. Mechanical Systems and Signal Processing, 2019, 131: 183-198. doi: 10.1016/j.ymssp.2019.05.053
    [75]
    NIU Gang, CAO Xue-jie, QIN Xiao-xiao. Research on fault detection and isolation of dual channel speed sensor for high-speed train[J]. Chinese Journal of Scientific Instrument, 2019, 40(1): 158-165. (in Chinese) http://www.cnki.com.cn/Article/CJFDTOTAL-YQXB201901020.htm
    [76]
    LU Jin-jun, WU Meng-ling, NIU Gang. Research on fault diagnosis method of speed sensor for brake system of rail transit vehicles[J]. Journal of the China Railway Society, 2021, 43(1): 85-93. (in Chinese) doi: 10.3969/j.issn.1001-8360.2021.01.010
    [77]
    ZHOU Dong-hua, JI Hong-quan, HE Xiao, et al. Fault detection and isolation of the brake cylinder system for electric multiple units[J]. IEEE Transactions on Control Systems Technology, 2018, 26(5): 1744-1757. doi: 10.1109/TCST.2017.2718979
    [78]
    SEO B, JO S H, OH H, et al. Solenoid valve diagnosis for railway braking systems with embedded sensor signals and physical interpretation[C]//Prognostics and Health Management Society. 2016 Annual Conference of the Prognostics and Health Management Society. New York: Prognostics and Health Management Society, 2016: 337-343.
    [79]
    AN D, KIM N H, CHOI J H. Practical options for selecting data-driven or physics-based prognostics algorithms with reviews[J]. Reliability Engineering and System Safety, 2015, 133: 223-236. doi: 10.1016/j.ress.2014.09.014
    [80]
    BARALDI P, CADINI F, MANGILI F, et al. Model-based and data-driven prognostics under different available information[J]. Probabilistic Engineering Mechanics, 2013, 32: 66-79. doi: 10.1016/j.probengmech.2013.01.003
    [81]
    LEI Ya-guo, LI Nai-peng, GONTARZ S, et al. A model-based method for remaining useful life prediction of machinery[J]. IEEE Transactions on Reliability, 2016, 65(3): 1314-1326. doi: 10.1109/TR.2016.2570568
    [82]
    DAIGLE M J, GOEBEL K. A model-based prognostics approach applied to pneumatic valves[J]. International Journal of Prognostics and Health Management, 2011, 2(2): 1-16. http://matthewjdaigle.com/pubs/DaigleEtAl-IJPHM-Valves.pdf
    [83]
    GAO Ze-hai, MA Cun-bao, SONG Dong. Aircraft fuel feeding system performance degradation and failure prediction[J]. Journal of Northwestern Polytechnical University, 2015, 33(2): 209-215. (in Chinese) doi: 10.3969/j.issn.1000-2758.2015.02.007
    [84]
    NIU Gang, HUANG Xiao-fan. Failure prognostics of locomotive electro-pneumatic brake based on bond graph modeling[J]. IEEE Access, 2017, 5: 15030-15039. http://ieeexplore.ieee.org/document/8002563/
    [85]
    LUO Jian-hui, PATTIPATI K R, QIAO Liu, et al. Model-based prognostic techniques applied to a suspension system[J]. IEEE Transactions on Systems, Man, and Cybernetics—Part A: Systems and Humans, 2008, 38(5): 1156-1168. http://ieeexplore.ieee.org/document/4604823/
    [86]
    ZHAO Shen-kun, JIANG Chao, LONG Xiang-yun. Remaining useful life estimation of mechanical systems based on the data-driven method and Bayesian theory[J]. Journal of Mechanical Engineering, 2018, 54(12): 115-124. (in Chinese) http://www.cnki.com.cn/Article/CJFDTOTAL-JXXB201812016.htm
    [87]
    SHEN Zhong-jie, CHEN Xue-feng, HE Zheng-jia, et al. Remaining life predictions of rolling bearing based on relative features and multivariable support vector machine[J]. Journal of Mechanical Engineering, 2013, 49(2): 183-189. http://www.cnki.com.cn/Article/CJFDTOTAL-JXXB201302030.htm
    [88]
    YOU G W, PARK S, OH D. Real-time state-of-health estimation for electric vehicle batteries: a data-driven approach[J]. Applied Energy, 2016, 176: 92-103. http://www.sciencedirect.com/science/article/abs/pii/S0306261916306456
    [89]
    ZUO Jian-yong, FENG Fu-ren, HE Yi-xin. Research and application of train online health status detection based on feedforward neural network[J]. Journal of Physics: Conference Series, 2021, 1828(1): 012034. doi: 10.1088/1742-6596/1828/1/012034
    [90]
    ZUO Jian-yong, ZHAO Tie-feng, WANG Bing-zheng, et al. Analysis of service condition and influence of metro brake system based on stream data processing method[C]//ASME. Proceedings of the 2018 Joint Rail Conference. New York: ASME, 2018: 1-4.
    • Relative Articles
    • Supplements(0)
    • Cited By

Catalog

    Get Citation
    PDF
    XML

    Article Metrics

    Article views (4928) PDF downloads(319) Cited by()
    Related

    Website copyright Journal of Traffic and Transportation Engineering Editorial Department陕ICP备05001904号-1

    Address ：Editorial Department of Journal of Traffic and Transportation Engineering, Chang'an University, Middle Section of South 2nd Ring Road, Xi'an, China（710064） Tel：029-82334388 Email：jygc@gfscw.cn

    All visit:Today's visit:

    Supported by: Beijing Renhe Information Technology Co. Ltd    

    /

    DownLoad:  Full-Size Img  PowerPoint
    Return
    Return